![]() Though it is such a friendly flow, some of these loops may end up being used. Most of what I am working up will get recorded. In my case I am using this set-up for quick-and-dirty demo stage workouts. For a bus, you can choose Loopy as s destination if you have AUM connected to Loopy in : those are good points. In AUM, when you choose Loopy as a source, you can choose any of Loopy's dials (tracks) as a source or Loopy's stereo output. Super powerful live looping and premixing said: I understand and would like to try this myself.Īny chance to get your AudioBus if you still need the AB3 preset, let me know and I will post it when I have my iPad available again which will be later today. You can use Loopy HD for instrumental loops triggering and Loopy for live recordings with individual loops predefined pan settings for example. But you’re right, monitoring lowest latency is even more important and that setup allow for that.īTW, a cool thing iPhone allows for that iPad don’t is ability to run both Loopy HD and Loopy for a total of 24 loops and extra main outputs mixing (especially stereo wideness with nice AUM effect node). It’s also possible to send individual Loopy outputs to AUM for live control with midi knobs/faders app/hardware controller. That also allows to have different sources in AUM and quickly switch between them or make sub mixes, set what is recorded in Loopy. With state saving they are a pretty good combo actually and reasonably stable. I’m super fussy about latency and this totally works for me. What has suggested in terms of monitoring does away with cumulative latency of running audio via AUM as well as Audiobus. ![]() I don’t believe we’ll ever see Loopy exposing its inputs to AUM’s output nodes. This is where Loopy and Audiobus integration comes in. Input channel has AUv3/IAA/Audiobus support. I find GTL more suitable for this purpose (from song composition loop based tool to routing into it as looper) but not multiple dedicated outputs, etc but is aware and even considering do it AUv3. With this preset, you need to keep Loopy monitoring settings off, and Ruismaker Noir in AUM can be replaced by anything else. ![]() I use AB beta and AUM beta, so perhaps this will not open correctly, let me know. Blocswave is also ideal for that purpose with more slots and multi export, but it’s less reliable than before since iOS 12 and no midi control.Įdit: Here is an AB preset. So it’s more a live tool than a production tool, but it all depends on your needs. And 12 loops is not a lot for a full song. Only thing missing is multi loop export, as you have to export each 44.1/16 loop individually. And Loopy allows for easiest recording process via touchscreen, or you can even uses a pedalboard/midi controller for advanced triggering via midi learn. AUM allows for recording loops, but you need to load each time each loop in a file player node to listen to your whole production. It will let you make multiple loops playing at the same time like if it was a mini DAW. This is the main purpose of Loopy if you want to use it for production: making some loops/music material in realtime. So AUM is better mostly for Loopy session/live gigging audio recording. While I haven't experienced feedback, it seems like a session recording uses AAC format, but loop recording uses 44.1 kHz 16 bits. (It also gives me pause that I have an AUM to Loopy lane in AB3 and a Loopy to AUM lane. That works, but it is a lot more involved than what I have a few people mention. ![]() I create sends to Mix Bus A for any channels that I want to record in Loopy.I set up Mix Bus A with the destination "1: Loopy HD" from the IAA/AudioBus Output destination popup.Add Loopy HD as an audio source with AUM as the destination.Add AUM as an audio source with Loopy HD connected as the destination.I have seen a reference somewhere to being able to choose AUM as the audio input source in Loopy (I have tried non-HD and HD) but have not been able to figure out how to do that. But I haven't figured out how to make it work without using AB3. I am using AB3, but I have seen a couple of people mention that you don't need AB3 - that AUM can send to Loopy. I have something that works, but I have a feeling that there is a more elegant way to do it. What is the best way to set up AUM and Loopy so that I can send from an AUM bus to Loopy to use as an input. Oftentimes, I am using Bias AMP or ToneStack as an input to bring in my guitar. I find it more convenient than working in a DAW. It lets me work up some bits and record precisely-timed loops that I can drop into BeatHawk or the like and also record non-looped bits. I recently realized that Loopy (HD) together with AUM is the right approach for an agile jamming/song sketching setup for me.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |